PDA

View Full Version : 35s & leveling kit


Cookie
04-03-2009, 03:54 PM
has anyone heard of 35s being a problem with only a leveling kit for 97 ram. im think id have plenty of room but figure id ask anyway.:dontknow:

bakelite
04-03-2009, 04:14 PM
Mine's a 92 so I know it's not the same but I run 33's on it no problem. I had some rubbing so I took the molding off the front wheel wells and it's okay now. I could run 35's on the back no problem and on the front too with a little creative cutting. [cheers]

Meeshies
04-03-2009, 04:51 PM
I was looking at doing that as well but was strongly recommended not doing it...

Mainly for the fact that it gives it a bit rougher ride with a leveling kit, *from what I'm told*, you don't wanna krank it to the full 2inchs because you will notice a difference in the driving and it'll make it a bit rougher..

Call Bryson @ Jeep Trills, he knows alllllll

DeeDee
04-03-2009, 05:32 PM
we have a leveling kit in ours and we are putting 35's on it.... have 33's right now and its fine [cheers]

230
04-03-2009, 05:34 PM
They will fit but they will be very tight.I had a 97 and tried 35's and took them off to put the 33's back on.

MetalMan
04-03-2009, 06:23 PM
If it's diesel it'll work, for a gas truck you might want to go 33's. Diesels sit higher to begin with so you can fit 35's under them no prob with a levelling kit.

B
04-03-2009, 06:35 PM
no prob's cookie hammer down ... and meehies yours is ifs so your leveling kit works totally different than his will on his solid axle

yours is a torsion bar set up his is a coil spacer

[cheers]

Meeshies
04-03-2009, 08:07 PM
gotcha... oh well ... in case anyone has a truck like mine... I look smart :D hahaha

Moondog
04-03-2009, 09:10 PM
Yep they fit with no problems at all Just rember to change your shocks as well as the factory ones make speed bumps interesting to say the least. Heres mine [cheers]

MetalMan
04-03-2009, 11:02 PM
That truck's hot, pretty much what I'd like to get my hands on. Those are 35's?

Moondog
04-03-2009, 11:08 PM
Yep 35" Mickey Thompson MTZs levelling kit dual 6" exhaust and cold air [36]

Cookie
04-04-2009, 01:27 PM
ya ive got 33s on now , im thinkin about getting the #5 fuel plate for more power. 35 is the way i want to go tho.
THANKS B

crazydude
04-04-2009, 03:22 PM
This my 2001 with a 2'' leveling kit with 35 mickey thompsons on it you get a bit of rub with the wheel fully cranked but nothing to worry about but mine is also the 4x4 offroad package which came 2 inches higher from the factory. Still drives the same but I would recommend a alignment after it is put in.

jesslee
04-04-2009, 05:49 PM
i got a 2000 diesel with a leveling kit and 35's, fits good, little rubbage at full crank

hrd4mud
04-14-2009, 10:54 PM
Mines an 01 offroad just like the black one above, has 35" toyo Mt's, it brushes against the back of the front wheelwell when turning if I hit a bump, but mine is a 2.5" leveling kit and the offroad is almost 2" taller to start.

In a 97 1500 with 2" leveling Id guess it will rub a fair bit whenever you turn, unless you take off that ridge in the plastic inner fenderwell.

I got mine from ebay in the states, shipped and everything was under 120 they are solid steel spacers, that bolt in, pretty strong setup, pretty easy to install, and I didnt have any alignment issues.

4linkfota
04-16-2009, 09:18 PM
I got a 98 2500 and fit 35's fine with very little rubbing if you got the right offset.