PDA

View Full Version : Who Does Body Work ?


UU
10-28-2008, 06:04 PM
I need some sheet metal work done on the rear window hatch of Willy. Cut out the rusty spots and make new pieces. I can take it in and drop it off no problem but its going to take more skill than I have to fix it.

Anyone know of a descent shop in the lower mainland that can do that ?

Thanks [cheers]

Moondog
10-28-2008, 06:34 PM
Got some pics of the area you need repaired Walt? I may be able to help you out;)

toyon35s
10-28-2008, 06:48 PM
metal work isnt that hard just takes pateince[cheers]

pumpkin
10-28-2008, 06:50 PM
I might know of someone, they usually work on older stuff, but I can check with them.

dirka dave
10-28-2008, 08:05 PM
Bondo my friend,lots of bondo.....

Apathy
10-28-2008, 08:28 PM
I might know of someone, they usually work on older stuff, but I can check with them.

how much older do you need? Its a 54? willy's

epic3
10-29-2008, 12:17 AM
I can help ya bud

pumpkin
10-29-2008, 06:49 AM
how much older do you need? Its a 54? willy's


The people I know build hot rods, in the 28 to 35 vintage. They are very good at making body panels. On occasion they do work on the new stuff,,,,,,,,40's and 50's.

UU
10-29-2008, 01:11 PM
94705

94706

94707

94708

94709

94710

94711

94712

dirka dave
10-29-2008, 01:15 PM
Eeeeek :eek: , thats worse than mine Walt.
I guess no more dirka's rusty toy jokes eh ? :p

I juess it's time to learn some sheet metal skills..:confused0006:

Moondog
10-29-2008, 07:19 PM
Sorry walt thats a little bit to much for me good luck with it though[cheers]

Trooper
10-29-2008, 07:31 PM
Thats allot of work to patch all that up. I can do it but I dont have the spare time. I do a ton of patch repairs to sheet matal parts. I have a power hammer, english wheel and tons of bucking pars at my shop. Its actually not that hard all your doing in stretching metal sheet metal is easy too. that corner you will need to cut releaf slots in.

UU
10-29-2008, 08:29 PM
it's just the bottom 3" that needs replacing, it doesn't need to be perfect just needs to fit and look ok (not a show truck). its the inner corner that are gonna take some skill


so any one know of a shop or want to take on a side job (not in a big hurry for it)

gavman
10-29-2008, 08:57 PM
This dude does bodywork[36]

Ironman
10-29-2008, 10:18 PM
i got a 15 lb sledge hammer. can i try to fix it:D

RIFF RAFF
10-29-2008, 10:34 PM
west coast repair and collision on 240th in maple ridge does good work and a good guy. about a month or more wait.

frogger
10-30-2008, 10:47 AM
theres a better and easier way to do this but it would cost you 400$ for me to do it for you i just did my 4runner and other rebuilts just call me ill explain it to you ,it will never show rust again.
eric 604 996 9912

boogyman
10-30-2008, 08:16 PM
thats an easy job if you want I could do it but don't have a shop I rebuilt the quarter panels on my Ramcharger if you want to have a look give a hollar 604-557-8817

UU
10-07-2009, 09:18 AM
OK, sorry about the delay guys, but I have 3 jeeps and this one is last on my to-do list.any ways, cleaned the tail gates up a bit for a better look, so if anyone wants to tackle this mess or knows of a shop that can, let me knowmore ugly picturesthe lift gate116360116361116362116363116364116365


the tail-gate116366116367116368116369



good thing there isnt 50lbs of bondo on it [16]

dirka dave
10-07-2009, 11:59 AM
That thing is almost as bad as my 82 WAS...



It must be hard and tiring repairing three jeeps, I would go nuts !:confused:



Any aftermarket stuff from the US ?





Whar about fiberglassing ?

toyon35s
10-07-2009, 04:58 PM
all in all that doesnt look that bad ,looks alot worse than it is,pm me your # and go grab a 4x2 sheet of 20gauge sheet metal from princess auto and a good pare of sheers and im sure we could do some thing with it ,its only lke 20$ for the sheet metal ad i have the welder just no shop to do it in but ive done all my shit in the elements[cheers]