PDA

View Full Version : Nissan engines


epic3
04-01-2008, 10:01 PM
Hey nissan weirdoes

is a 300z motor from a 90-up 300z compatible with a nissan truck of anysort??


If so I got one with 64000km's for sale (non turbo):D

factor
04-01-2008, 10:02 PM
shut up meathead nobody wants your junk

epic3
04-01-2008, 10:07 PM
SHUUUUTTTIT!

redman
04-01-2008, 10:30 PM
SHUUUUTTTIT!



:gives: and shut up phil

epic3
04-01-2008, 11:16 PM
SHUTTTTTIT

Ironman
04-01-2008, 11:24 PM
go sign up on a ricer forum noone likes you here anyways

epic3
04-01-2008, 11:29 PM
SHUUUUTTIT

MikeWild
04-01-2008, 11:33 PM
<insert witty Phil bashing comment here>


oh yeah and shut up phil

epic3
04-01-2008, 11:35 PM
Like he'll ever get his next project done or even close to the track<insert witty Phil bashing comment here>


oh yeah and shut up phil

Hows that

Pegleg
04-03-2008, 07:01 PM
so does it fit???????

Apathy
04-04-2008, 09:07 AM
If its a Duel overhead cam.. it will not fit in a truck or pathfinder wihtout lots of cutting and banging sheet metal.

If its single overhead cam yes it will fit, but they changed the wireing harness sometime in early 90's so that could also be an issue.
The blocks are the same.
There were two different block versions, one with a short crank snout one with a long crank snout. But i'm not sure which ones came in which.

You can alwasy take the block and heads, transfer all your sensors, intake and exaust from YOUR rig and bolt them up to the VG30 block.

epic3
04-04-2008, 12:13 PM
what your sayin is hood scoop right Jer? Big freakin wide hood scoop this is in a car complete that I will be strippin for parts for another one

Apathy
04-04-2008, 12:21 PM
no not hood scoop. The duel overhead cam heads on those are twice the size of the single overhead cam heads. They just don't fit in the engine bay.

Its easier to drop in a SBC than a Duel overhead cam VG30

epic3
04-04-2008, 12:22 PM
yes they will I can show you how

Apathy
04-04-2008, 12:24 PM
for christ sakes phil.. i said you could, with lots of sheet metal trimming and bashing.

Go to some nissan forums and check it out.

epic3
04-04-2008, 12:43 PM
I know

norm
04-05-2008, 07:08 PM
90 up 300's were all twin cam,bellhousing will bolt to pickup,pathfinder trans that had v6.you would need harness and ecm tho.would be a shitload of hassle[16]

Newfie
04-11-2008, 04:55 PM
My buddy has a 300 non turbo and it has a lot of mid to high end like the 7mge. I would think it would be a bad swap for a low speed 4x4.:dontknow:

Apathy
04-12-2008, 07:47 AM
depends on the tranny and overall gear ratio.

These little engines have more torque than almost any small v6

factor
04-12-2008, 10:43 AM
idiot

epic3
04-12-2008, 01:04 PM
My buddy has a 300 non turbo and it has a lot of mid to high end like the 7mge. I would think it would be a bad swap for a low speed 4x4.:dontknow:

It probably has stretched timing belts



Mine dont



so you gonna buy it Pathy:D

Apathy
04-13-2008, 06:45 AM
no.. sorry epic. not gonna happen.. don't have the funds right now.

epic3
04-14-2008, 06:17 PM
dont worry it might be goin into another car a frankenstien of sorts hehehe