PDA

View Full Version : b2 going under the knife soon.... again.....


Squishy
05-01-2007, 10:08 PM
got the 60 rear cleaned up today, hopefully ill get the 60 front here soon and do the same, then build the 3 link suspension for the front then figure out if im going to link the rear or just leave it, those are hummer double beadlocks, ott arms, 1350 u joint and yoke for the 60.....

m j
05-01-2007, 10:26 PM
where did you get the hummers?
I want another set

Honky
05-01-2007, 10:30 PM
Right on looking good Squish! [36]

Squishy
05-02-2007, 04:06 AM
got the hummers from some kid in surrey

jhunter
05-02-2007, 09:00 AM
nice thats gonna be sweeeeet

brandonf250
05-02-2007, 07:20 PM
fuckin awsome cris

Cheeky
05-02-2007, 09:17 PM
got the hummers from some kid in surrey

:eek: shouldnt be playing with the little 1's[16]





































:D

mini
05-02-2007, 09:23 PM
what are you doing with your old 44 and what gears are in it?

C-Dog
05-02-2007, 10:26 PM
got the hummers from some kid in surrey




Of course where else would they come from [15] [15] [15] [15]


Oh and the new bling looks sweet the build thread will be gooder

Squishy
05-03-2007, 01:16 AM
old axles are 5.13 gears, dana 44 front, fullsize 8.8 rear, detroit locker in the rear also

brandonf250
05-03-2007, 06:35 PM
sent u pm

jakerngr
05-03-2007, 08:07 PM
so there is a hummer on blocks in surrey then???

Squishy
05-04-2007, 03:58 AM
ordering this stuff up today, all the brackets for the front 3 link, rear caliper brackets too:cool: hopefully ill remember to order in the link material also

HEAVY METAL
05-04-2007, 08:16 AM
wicked dude...

Murd0c
05-04-2007, 08:42 AM
fricken sweet squish except ou should really shave those diff's [f]

Squishy
05-04-2007, 02:50 PM
fricken sweet squish except ou should really shave those diff's [f]

ill just bounce it over whatever comes in my way, i should still have reasonable ground clearance on the 38.5's

Squishy
05-04-2007, 02:52 PM
so there is a hummer on blocks in surrey then???

there is 3, i could only get one rim off of the 1st 2 before the alarms went off:party0010:

Murd0c
05-04-2007, 06:40 PM
ill just bounce it over whatever comes in my way, i should still have reasonable ground clearance on the 38.5's

u sure about that :dontknow: , might be better off doing now rather then later

Squishy
05-04-2007, 06:41 PM
u sure about that :dontknow: , might be better off doing now rather then later

yup im sure, and i dont have the tools or the experience to shave it either, so thats out

Ugly
05-06-2007, 11:08 PM
shave it?

mark
05-13-2007, 12:36 AM
damn nice arms. what did those set you back?

Squishy
05-13-2007, 10:09 AM
too much, 220 an arm i belive

Squishy
05-16-2007, 08:26 PM
just finished welding all the brackets together, should have pics up tonight

Squishy
05-17-2007, 02:20 PM
heres the brackets

Murd0c
05-17-2007, 06:51 PM
looking awesome squish [36][36][36][36][36][36]

Squishy
05-17-2007, 07:24 PM
just need to get a set of tires to wheel the front diff around on and i can start welding the brackets in place on the diff, and then figure out my links(what material, length)

im gonna buy a set of probably 70-80% tsl's im going to run, 39.5x15x16.5

brandonf250
05-17-2007, 08:01 PM
lookin good

Squishy
05-21-2007, 05:36 AM
:D pick tires up whenever i want this week, and got this done yesterday, bling bling[22]

HEAVY METAL
05-21-2007, 06:37 AM
cool man...gonna be big truck

brandonf250
05-21-2007, 11:33 AM
nice gonna be nice,,what does DIG stand for?

mark
05-21-2007, 01:40 PM
nice what are those calipers off of anyways?

Squishy
05-21-2007, 01:43 PM
nice gonna be nice,,what does DIG stand for?


inside joke, just kinda happened while workin on it, and let the DIG stay rather than grind it off

calipers are off a 3/4 ton 4wd chev front

drknyght
05-21-2007, 04:26 PM
Looks good Chris, those rear disks went together easy? , you still tryin to find a place to throw it all together? How long you figure for time for final assembly?

Squishy
05-21-2007, 04:50 PM
discs went together really easy, brackets worked out perfect

it will probably take me a week or two max, ive got 95% of everything here allready, just need a place to assemble it.

brandonf250
05-21-2007, 06:30 PM
what u using for an e-brake? or gonna not worry about one

Squishy
05-21-2007, 09:10 PM
not gonna worry, it'll rarely be on the street, probably add some linelocks thouhg

Squishy
05-25-2007, 02:38 AM
lower links are almost done, think ill bend em?

UU
05-25-2007, 08:33 AM
lower links are almost done, think ill bend em?

You ? yuppers :D

patford
05-25-2007, 08:50 PM
Seen you were looken for 35 spline axles for a dodge , going to put
then in your d-60 or do you have a emty d- 70 ?

Squishy
05-25-2007, 11:16 PM
the rear 60 is getting 35 spline axles, i hope i dont have any problems

patford
05-26-2007, 09:54 AM
asken the questions cause my 38" took out stock 60 axle fast , heavy
truck . Best price found to bore housing $200 and the guy is just swamped
has not got back to me. What your luck been like or did you find a large
bore housing ?

Squishy
05-26-2007, 03:50 PM
nope, gonna do it myself

patford
05-26-2007, 08:35 PM
is that the one from priate ? was thinking about trying it , but chicken
out, let me know how it goes . Have you found axles yet ?

Squishy
05-26-2007, 09:03 PM
yeah got the idea off pirate, there is no reason it wont work, and its cheep.

havnt found axles yet but havnt really been looking, wont be hard, dana 70 single wheel axles are the same length and come in 35 spline, and will bolt in

Explorer guy418
05-26-2007, 10:57 PM
wut size tires u going with this thing?

Squishy
05-26-2007, 11:32 PM
39.5x15

patford
05-27-2007, 05:05 PM
Hey my stock d-60 axles were 34.75 " and ones given to me d-70 were
35 1/8 " , so need to make spacers , somthing to look out for . This is
the same story a guy had on 4wheeler.ca. Hope this mite help or you
could tell me somthing

Squishy
05-27-2007, 05:30 PM
i pulled dustbins rear axle(dana 70) and both the 60 and 70 shafts were the same length. they are both dodge diffs though, so that might have something to do with it?

gordwould
05-28-2007, 10:16 AM
lookin good there kris how long before its movin on its own?

Squishy
05-28-2007, 10:19 AM
end of june forsure it will be driveable(makeshift using old driveshaft, no lockers or gears), weather ot not ive found gears, lockers and driveshafts im not sure, thats alot more $$$ than ive got to put into the truck right now

C-Dog
05-28-2007, 07:36 PM
Gotta love progress man thats some neat shit your doing to the diff boring it out and shit [36] [36] [36] [36]


Its going to be a cool ride when its alll dialed in [cheers]

Squishy
06-17-2007, 05:39 PM
:party0010: :party0010: :party0010:

Troy
06-17-2007, 09:31 PM
nice. i have a familiar looking pile of parts like that right now too. Where did your order the ram from?

Squishy
06-17-2007, 09:48 PM
pscmotorsports out of the states, 8" ram, 1.5" stroke, .625 rod. going to have to limit the ram, but ill get to that once its on the truck

Squishy
11-22-2007, 05:15 AM
i guess this is progres:dontknow: how the truck sits as of now

damn B! i wish i ordered the pre welded btf cover, my welds are BUNNNNK:D

Leithmc
11-22-2007, 09:00 AM
Those welds are awesome.

brandonf250
11-22-2007, 06:48 PM
nice welds kris looking good

patford
11-22-2007, 10:31 PM
whats the tab for on the cover ? axle trust ?

Squishy
11-22-2007, 10:35 PM
whats the tab for on the cover ? axle trust ?

it is made for a truss, but im going to mount my hydraulic ram off of it if space permits, if not, ill just chop that section of it off

Ginger Snaps
11-22-2007, 10:52 PM
fucken looken kill bro!

see yeah sunday sunday sunday!

yoda thrills
11-22-2007, 11:54 PM
i havnt seen much progress ive actually enver seen it run a trail yest kris wuts up with that??

Squishy
11-24-2007, 05:27 AM
i havnt seen much progress ive actually enver seen it run a trail yest kris wuts up with that??


:fighting0071: can it newbie

Redneck Lincoln
11-24-2007, 08:33 AM
i havnt seen much progress ive actually enver seen it run a trail yest kris wuts up with that??

[16]

Punk in Drublic
11-26-2007, 11:52 AM
idont see uttin wrong whith em welds. better than some of the lazy fucks at work.

Squishy
11-27-2007, 04:25 AM
idont see uttin wrong whith em welds. better than some of the lazy fucks at work.

it would hold, but im not proud of the welds, basically re lernt how to weld while building that cage, it was a learning process