PDA

View Full Version : tire clearence


chevy69chevelle
10-14-2004, 06:39 PM
I just got a 3/4t F250 and was wondering if my truck could clear 35X12.5 BFG mudders w/ a 3" body lift. i know they will fit, but steering and travel wise, will they rub?

Punk in Drublic
10-15-2004, 05:56 AM
hack the fenders[5]

Necrophilia: roll over and crack open a cold one

sj-x 500
10-15-2004, 06:10 AM
what year? the new style will just clear em

zuk: being prepared for total tear down. yota's 5.29's arb's.
ford: it drives.

In The Zone
10-15-2004, 08:08 AM
I clear 36" swampers with lots o room on my 97 F150 then again it is modified....... un like yours....

im going to 39"s next with my SaS

depends on what u want to do with it rocks? Mud ?
or allpurpose.

It is Parked and under construction....
Soon to be on a trail near U

chevy69chevelle
10-15-2004, 02:57 PM
It's an 88, and kind of all purpose, but more mud. I love mud, always have. may have seen my van up at stave iu was up there( and ggot stuck) quite a bit. it was brown, ugly, and free. but i think if they do rub i might just hack the fenders, we are makin new bumbers anyways.

In The Zone
10-15-2004, 05:22 PM
u will be fine then fenders will go eventually anyway...

ya mud is fun not a lot o flex need there but definatly good clearance....

good luck...



It is Parked and under construction....
Soon to be on a trail near U

barracuda
10-15-2004, 05:43 PM
I will be haveing a one piece drop bracket soon if you wanted to lift it.

Image Insert:
http://www.funinbc.com/forum/uploaded/barracuda/20041015234339_fordm lift bracket.jpg
8.99KB

"A level" mobile welder
migImage Insert:
http://www.funinbc.com/forum/uploaded/barracuda/200361401938_scan0001.jpg
32.46 KB

,tig,alum spool,stick
rates start at $65 an hr
welder rental from $125 per day

The way to a mans heart is through his zipper!!!

chevy69chevelle
10-16-2004, 08:45 PM
ya, paid 400 for the truck. starter soudns funny(flex plate is a lil stripped) and the front drivers side u-joint(for 4 wheel) is going, but i got a new one, just gotta put it in. it'll prolly brake tomorrow, goin up to stave or catermal(by pick-a-part) to dick around. for now i got a 3"lift and puttin my 35"s on next week sometime

chevy69chevelle
10-16-2004, 08:57 PM
one more question, is it possible to take the posi set-up out of a straight axle dana 44 and put use it to convert my front end to posi? i believe it's a dana 44 as well, from what i was told, haven't really searched any numbers yet.

BeerBaron666
10-17-2004, 05:58 AM
88 I'm guessin it's a ttb still? I'm pretty sure you can, the interals are the same. You will have a 44 in your truck and as long as you getting the peices out of a 44 you should be good.

-------------------------------
Anger management pisses me off!!
-----------------------
"Ah, devil ether. It makes you behave like the village drunkard in some early Irish novel. Total loss of all basic motor function. Blurred vision, no balance, numb tongue. The mind recoils in horror, unable to communicate with the spinal column. Which is interesting because you can actually watch yourself behaving in this terrible way, but you can't control it."-Raoul Duke

chevy69chevelle
10-17-2004, 08:04 AM
awesome, then I'll prolly do that for now untill i get a lil mor money to do somethin more, at least i'll have posi in front then, and rear. no more 3 wheel drive haha. I got the dana 44 sittin in a truck we are scrappin in next couple of days. but off to pick-a-part, L@TEŽ