PDA

View Full Version : Easiest way to remove 22r motor??


purplemonster
06-06-2011, 12:39 AM
I'm planning on getting a couple buddy's and some beer next weekend to remove my toyo motor and install a new fresh 22r motor so my question is what's the easiest way to remove the 22r without tranny and then when installing the next motor I want to delete most of the unescesarry things like egr or??

Work is being done on a 87 toyo pickup lifted 6inch

4skin
06-06-2011, 12:44 AM
cutting torch is easiest to get it out but sucks to put one back in after
so unbolting it is probably eaisier

youngun
06-06-2011, 01:41 AM
so unbolting it is probably eaisier

My thoughts exactly

dirka dave
06-06-2011, 08:32 AM
Pm sent

UU
06-06-2011, 08:43 AM
sell it whole and buy a jeep

:D

Tunabomber
06-06-2011, 09:00 AM
tow strap [36]

crazylike
06-06-2011, 09:18 AM
probably easier to remove it all and swap motor out of vehicle then put it all in again. just remove the grill rad ect, trans bolts wiring t case wiring wiring on motor motor mounts and yank it all. or if you really don't wanna remove trans then take the 7 or 8 bolts from the bell housing and ease it forward slowly till the shaft clears then follow steps in reverse to reinstall.

Nutbar
06-06-2011, 10:33 AM
There is no problem that can't be solved with the proper application of explosives

youngun
06-06-2011, 11:29 AM
There is no problem that can't be solved with the proper application of explosives

Another valid point

RCCruiser
06-06-2011, 05:45 PM
You say in a different post that it's just a blown head gasket.
It's much easier to replace said head gasket than it is to pull the engnine.

If you do end up pulling the engine, I find it's easier to leave the tranny and t-case in place, and pull just the engine.
Removing the radiator makes it a lot easier, too.

Trailjunkie
06-06-2011, 05:49 PM
hit truck with bat, whatever falls off that isn't rust is probably motor. lol

harvester_sorrow
06-06-2011, 07:06 PM
sell it whole and buy a jeep

:D


You could get like 5 jeeps with the money.[36]

purplemonster
06-06-2011, 08:17 PM
Ill take some pics of the motor then it will be a better understanding for everyone on why the old motor needs to go... Let's just say old owner did the head gasket but I think he forgot to put the head gasket on the block followed by alot of other gaskets so there's oil and grim everywhere!

mus-Tard
06-06-2011, 08:20 PM
actuly it is easer to remove the fenders, hood, cab, fraim, suspention, drive line from around the motor than it is to remove the moter from the fenders, hood, cab, fraim, suspention, drive line....

SHITTY
06-06-2011, 08:24 PM
sawsall, solves all

4skin
06-06-2011, 11:47 PM
unbolt stuff roll on roof motor should fall out

BrokenToy
06-07-2011, 01:25 AM
dont listen to the dutch Just pull the engine [15]

4skin
06-07-2011, 09:59 PM
dont listen to the dutch Just pull the engine [15]
dont listen to this guy longest toyota non build in history
nice porn collection though:D

BrokenToy
06-09-2011, 02:41 AM
ya i may be slow but at least i ant dutch [15]